rilpoint_mw113

VATIS Update Waste Management . Jan- Mar 2012

Register FREE
for additional services
Download PDF
Waste Management Jan- Mar 2012

ISSN: 0971-5665

VATIS Update Waste Management is published 4 times a year to keep the readers up to date of most of the relevant and latest technological developments and events in the field of Waste Management. The Update is tailored to policy-makers, industries and technology transfer intermediaries.

Editorial Board
Latest Issues
New and Renewable
Energy
VATIS Update Non-conventional Energy Oct-Dec 2017
Bio
Technology
VATIS Update Biotechnology Oct-Dec 2017
Waste
Management
VATIS Update Waste Management Oct-Dec 2016
Food
Processing
VATIS Update Food Processing Oct-Dec 2016
Ozone Layer
Protection
VATIS Update Ozone Layer Protection Sep-Oct 2016
Tech
Monitor
Asia-Pacific Tech Monitor Oct-Dec 2014

Contents

__NOTOCNUM__

IN THE NEWS

China’s offshore wind power booms

China has made substantial progress in boosting its burgeoning offshore wind power by launching its largest inter-tidal wind farm at the end of 2011. On 28 December, Longyuan Power, China’s largest wind power developer, connected 99.3 MW of wind turbines to the grid in a pilot inter-tidal wind farm in Rudong county in Jiangsu province. Taking into account the existing 32 MW turbines, Longyuan has 131.3 MW turbines integrated to the grid in the pilot wind farm in Rudong. This has made the Rudong inter-tidal project China’s largest offshore wind farm. Inter-tidal wind farms – in regions that are submerged in high tide and heaved out in low tide – are a unique form to tap offshore wind power.

According to China’s Wind Power Development Roadmap 2050, the country plans to have 1,000 GW of installed wind capacity by 2050 – which makes up 17 per cent of its electricity consumption. So far, wind power generation accounts for 1.5 per cent of national power generation. The first stage of the inter-tidal wind farm pilot project, set to be 150 MW in installation, involves an investment of 2.5 billion yuan (US $397 million). It will be fully completed by March 2012, stated Mr. Zhang Gang, General Manager of Longyuan Jiangsu Offshore Wind Power. Mr. Zhang said the wind farm will annually generate 330 million kWh of electric power for the grid. He said that the company has overcome high installation cost in offshore wind farm construction through measures such as improved technology for single pile foundation and multi-pile jacket foundation forms. It has reached the European advanced level in technology for offshore wind farm construction, while also lowering offshore wind installation costs to 16,000 yuan/kW, about 60 per cent of the European level, he claimed.
Source: http://english.cri.cn

Renewable energy funding to go up in India

Power Finance Corp. (PFC), India’s largest state-run lender to electricity utilities, plans to more than double lending for renewable energy projects within a year, as coal-fired plants become riskier investments. PFC’s approved loans to projects, particularly solar and wind plants, will increase to Rs 15 billion (about US$300 million), or 4 per cent of the total in the next financial year, from Rs 6.75 billion (US$135 million), or just 1.2 per cent in the year ending in March 2012, Mr. Satnam Singh, PFC Chairman, said. “Given that fossil fuel costs have gone up, investments in wind and solar are surging,” Mr. Singh said, adding that PFC is ready to get into renewable in a big way where lending happens much faster. India’s Prime Minister Mr. Manmohan Singh plans to spend more than US$300 billion to expand the country’s electricity systems as part of an attempt to spur 9 per cent economic growth by 2017. An increasing share of that may go to clean energy projects, as lenders shun new conventional power projects that are facing risks such as the ever-increasing costs of non-renewable fuels.
Source: http://www.businessweek.com

Viet Nam targets 11 per cent renewable energy exploitation

Viet Nam has tapped only 5 per cent of its renewable energy potential and the government, under its National Energy Development Strategy, has set the target to increase this to 11 per cent by 2050.

Viet Nam gets around 2,000-2,500 hours of sunshine per year, with a solar energy density averaging about 150 kCal per cm2, equivalent to 43.9 million tonnes of oil per year. The total wind energy potential is estimated at 713,000 MW. Viet Nam has around 1,050 potential sites for small hydropower (up to 30 MW), identified with a total capacity over 4,000 MW, equivalent to 16.7 million GWh per year. In addition, Viet Nam also has more than 300 hot streams with temperatures ranging from 30° to 148°C, taking the geothermal power potential to 1,400 MW. The biogas energy potential in the country is estimated at 6.4 million tonnes energy equivalent (MTOE) per year.

The energy development strategy targets increasing renewable energy share to about 5 per cent of the total commercial primary energy supply by 2020, 8 per cent (approximately 9 MTOE) by 2025 and 11 per cent (approximately 35 MTOE) by 2050. Master Plan for Renewable Energy has been submitted to the government for final approval.
Source: http://english.vietnamnet.vn

Bangladesh launches renewable energy platform

Bangladesh Solar and Renewable Energy Association (BSREA) – a platform for renewable energy products businesses – was launched recently in Dhaka. Mr. Tawfiq-e-Elahi Chowdhury, Energy Adviser to the Prime Minister, inaugurated the association. BSREA aims to promote renewable energy in Bangladesh and keep track of the fast growing renewable energy industry around the world, said Mr. Dipal C. Barua, President of the new body. The 49-member BSREA will work to educate people on solar energy. “Our goal is to make Bangladesh a solar energy-rich nation, which can be achieved when 51 per cent or more of the population utilizes solar power,” said Mr. Barua, who is also the Chairman of Bright Green Energy Foundation. BSREA will also work for standardization and quality control of all the renewable energy products and services being sold in Bangladesh, the Association said.

The government plans to generate 500 MW (about 5 per cent) of the total electricity requirement from renewable energy sources by 2015 and 10 per cent by 2020. The government is working to formulate the Sustainable and Renewable Energy Development Agency (SREDA) to better regulate the growing sector, Mr. Chowdhury revealed. The government will extend all necessary support to BSREA in finding more avenues where renewable energy could be installed, he said.
Source: http://ph.news.yahoo.com

Indonesia to expand use of renewable energy for electricity

Indonesia’s state-owned electricity firm (Perusahaan Listrik Negara, PLN) plans to boost the use of renewable energy for electricity to 20 per cent from the current level of 11 per cent in the coming eight years, a statement from the company said. To achieve this, PLN would promote development of renewable energy sources such as hydropower, geothermal, solar energy and biomass. The archipelago has abundant renewable energy sources.

Many of Indonesian power plants still use fossil fuel and coal, whose reserves keep declining while the energy demand keeps rising by over 7 per cent annually. Indonesia’s oil production in 2011 is forecast to lower than the target, because of technical problems and extreme weather, Mr. Raden Priyono head of oil and gas regulator BP Migas said. The country’s oil production has been on a decline since 1998 and led to its exit from the Organization of the Petroleum Exporting Countries (OPEC) in 2009.
Source: http://www.asean-cn.org

Philippines to test jatropha biodiesel from Malaysia

The Philippine government is subjecting to fuel standard testing the jatropha biodiesel from Malaysia-based Bionas, which is offering to supply what it claims would be the world’s first jatropha biodiesel. The Department of Energy (DoE) is expected to evaluate Bionas’s biofuel under a Philippine National Standard (PNS) on biodiesel.

Bionas Philippines Corp. (BPC) set up a jatropha oil processing plant in Zamboanga del Norte province in 2011. Its parent firm in Malaysia claims to be a global leading brand in jatropha plantation and biofuel with two processing and blending plants. Although the Philippine government has shelved research and development (R&D) for jatropha biofuel, BPC is optimistic about getting clearance for its jatropha biodiesel.

Philippine Agricultural Development and Commercial Corp. (PADCC) President Mr. Marriz B. Agbon said the government has not renewed interest in R&D on jatropha biodiesel, as the thrust is more on augmenting local production of ethanol for biofuel mix with petrol. While the Philippines has a biofuel policy that mandates coconut methyl ester mix at less than five per cent, Bionas has a B20 biodiesel composed of 50 per cent of diesel, 30 per cent of Bionas fuel, and 20 per cent Bionas diesel additives.
Source: http://thegreenreporter.wordpress.com

Malaysia aims at nationwide biodiesel use in two years

Malaysia is targeting for biodiesel B5 use to go nationwide by 2014, said Mr. Tan Sri Bernard Dompok, the Plantation Industries and Commodities Minister. The implementation could not be made earlier as there were not enough blending facilities for the alternative fuel, the Minister said.

B5 is a blend of 95 per cent regular petroleum-based diesel and 5 per cent palm methyl ester, which can be used in normal diesel engine vehicles without modification. Mr. Dompok also said his ministry was studying ways to reduce the quantity of regular diesel in biodiesel by increasing the use of palm methyl ester. The B5 programme, first introduced in 2006, is being implemented in phases in the central region of Peninsular Malaysia since June 2011.
Source: http://thestar.com.my

China’s solar market set to expand

China is aiming to reduce the cost of domestic solar power and expand the domestic market to better develop the photovoltaic (PV) industry during the 12th Five-Year Plan period (2011-2015), stated the Ministry of Industry and Information Technology. As per the industry plan announced by the Ministry, the cost of solar power per kWh will be reduced to 0.8 yuan (US$ 0.12) by 2015 and 0.6 yuan by 2020 and production of solar panels will be increased.

Meanwhile, the plan said the government requires China’s leading polysilicon manufacturers to reach a production capacity of 50,000 tonnes per year by 2015. Solar panel makers will have to reach 5 GW of annual production capacity by the same year. “It is time for integration of the industry,” said Mr. Wu Zhonghu, an expert with the China Energy Research Society. Mr. Wu said many small companies have started producing PV panels to pursue profits in the domestic market because their technology and production lines do not meet the standards applied overseas. The industry faces several obstacles such as high costs, shrinking overseas markets and a lack of laws and regulations to supervise the industry. If the government suspends subsidies to the solar companies, it would be difficult for them to sell in the domestic market because of high prices, he said.

The government plans to help companies in the solar sector increase annual sales. It aims to have at least one company reaching 100 billion yuan (US$15.8 billion) in sales by 2015, and between three and five companies reaching half that figure by the same date. The plan is expected to bring opportunities for thin-film PV panels, as the country will put more effort into Building Integrated PV. Eighty per cent of solar equipment and auxiliary materials will be produced domestically, according to the plan.
Source: http://english.peopledaily.com.cn

Philippines approves six geothermal deals

The Department of Energy (DoE) of the Philippines approved six geothermal power contracts in 2011, as the country aims to become the world’s largest producer of geothermal energy. The Philippines is currently in the second position, next to the United States. Geothermal power accounted for 14.7 per cent of the power generation mix in the country in 2010.

DoE approved the contract of Pan Pacific Power Philippines Corp. for geothermal projects in Benguet, Cagayan and Abra provinces. Pan Pacific, according to DoE, is a local company with a foreign partner. It is building a 600 MW hydropower project in Apayao, and is also developing small hydropower projects. DoE also approved the geothermal projects of SKI Construction Group Inc. in San Juan, Batangas, Tiaong in Laguna, Quezon, and Batangas and Tayabas-Lucban in Quezon.
Source: http://manilastandardtoday.com

India’s largest solar energy plant starts production

In India, a 40 MW solar power generation plant, set up in Jaisalmer district of Rajasthan, started power generation recently. The plant, which is currently the largest such facility in the country, was inaugurated by Union New and Renewable Energy Minister Mr. Farooq Abdullah and the state’s Chief Minister Mr. Ashok Gehlot. The plant owned by Reliance Energy was built at an estimated cost of Rs 4 billion (US$74.6 million) on 140 hectares of land. The plant will generate 72 million units of power.

On the occasion, Mr. Abdullah said that the country has set target to produce 20,000 MW of solar energy by 2022. He said that 90 per cent of the country’s power generation fund is spent on coal, petrol, diesel and natural gas. In such situation, wide usage of solar and wind energy would add a new dimension to the energy sector. Stating that Rajasthan was number one in India in solar energy exploitation, Mr. Gehlot said that there was large scope of expansion in the sector. Efforts were being made to set up a solar energy park in Rajasthan and to develop the state as a solar hub, he said. The state’s solar energy policy had incorporated more investments and incentives to the investors. He said Rs 100 billion (US$1,865 million) was being invested in this sector.
Source: http://articles.timesofindia.indiatimes.com

Palau airport takes to solar energy

The International Airport at the Re-public of Palau has adopted a green approach. The new solar panel array at the airport is a big deal for such a small nation and sets an example for other countries. The Republic of Palau, an island nation situated in the Pacific Ocean 800 km east of the Philippines, occupies an area of just 459 km2. About 85 per cent of the country’s electricity generation is fossil fuel based.

In December 2011, its international airport switched on a 226 kW solar panel array, supplied by Kyocera Corporation, Japan, and funded by the Japanese government’s Official Development Assistance (ODA). The first grid-connected solar power system in the country, Palau airport’s solar farm is made up of 1,080 Kyocera 210 W solar modules. Kyocera estimates the system will generate 250 megawatt-hours of electricity annually, avoiding approximately 80 tonnes of carbon dioxide emissions each year. The solar panels also provides shade in the airport’s parking lot, where they are installed. The modules have been reinforced with extra support to increase wind-pressure resistance.
Source: http://www.energymatters.com.au

PLASTIC WASTES

Process converts polyethylene waste into carbon fibre

Polyethylene used in plastic bags could be turned into something far more valuable through a process being developed at the United States Department of Energy’s Oak Ridge National Laboratory (ORNL). A team led by Mr. Amit Naskar of the Materials Science and Technology Division has described a method that allows not only for production of carbon fibre but also the ability to tailor the final product to specific applications. “Our results represent what we believe will one day provide industry with a flexible technique for producing technologically innovative fibres in myriad configurations such as fibre bundle or non-woven mat assemblies,” Mr. Naskar said.

By utilizing a combination of multi-component fibre spinning and their sulphonation technique, the ORNL scientists demonstrated that they can make polyethylene-base fibres with a customized surface contour and manipulate filament diameter down to the submicron scale. The patent-pending process also allows them to tune the porosity, making the material potentially useful for filtration, electrochemical energy harvesting and catalysis. The sulphonation process allows for great flexibility, because the carbon fibres exhibit properties that are dictated by processing conditions. For this project, the researchers produced carbon fibres having unique cross-sectional geometry – from hollow circular to gear-shaped – by using a multi-component melt extrusion-based fibre spinning method.

The possibilities are virtually endless, according to Mr. Naskar, who described the process. “We dip the fibre bundle into an acid containing a chemical bath where it reacts and forms a black fibre that no longer will melt,” he said. “It is this sulphonation reaction that transforms the plastic fibre into an infusible form. At this stage, the plastic molecules bond, and with further heating cannot melt or flow. At very high temperatures, this fibre retains mostly carbon and all other elements volatize off in different gas or compound forms,” Mr. Naskar explained.
Source: http://www.ornl.gov

New recycling method for plastic materials

Fraunhofer-Gesellschaft zur Forderung der Angewandten Forschung E.V., Germany, has taken a United States patent on a method for recycling plastic materials that contain at least two polymers, copolymers or blends thereof based on polystyrene. The method seeks to recycle plastic materials, eliminating the disadvantages of current methods, and enable simple economical recovery of polymers based on polystyrene. The method may be used for recycling any plastic material, in particular plastic materials from e-waste processing and from shredder light fractions.

The plastic material is mixed with a solvent for the polymers, copolymers or blends. A precipitation is then effected by the addition of a corresponding precipitant so that the gelatinous precipitation product can be separated from the further components of the plastic material. A particular feature of the present invention is that two incompatible polymers, which are based on polystyrene, can be separated as two separate phases. It is crucial that the precipitant and/or the quantity of the precipitant is chosen in a ratio to the solvent such that the mixture of solvent and precipitant has a value for the hydrogen bonding strength dH of the Hansen solubility parameter of 11 to 13Ö{square root over (MPa)}.

The method has the advantage that the precipitation can be effected economically in agitation tanks at low temperatures, preferably below 100°C., because of which no thermal damage occurs to the polymers. The polymer phases are thereby separated on the basis of their different material properties to form highly pure products with very good rheological and mechanical properties that enable them to be used as substitute for virgin material. Further, the quantity of solvent used can be reduced so far that the operation can take place with polymer gel and the solvent residue can be withdrawn mechanically in an economical manner. The separation of the remaining solvent is then effected in parallel and directly subsequent to the phase separation.
Source: http://www.freepatentsonline.com

Method of recycling laminated moulding

Kureha Corp., Japan, has secured a United States patent on an improved method to recycle a shaped laminate product, particularly a bottle. The process entails the steps of: breaking a moulded laminate product that has at least one layer of an aliphatic polyester resin, particularly glycolic acid polymer, in addition to a principal resin layer; storing the resultant broken pieces in a moisturizing environment to adjust the moisture content of the aliphatic polyester resin layer to at least 0.5 wt. per cent; and then washing the broken pieces with alkaline water to remove the aliphatic polyester resin layer, thereby recovering the principal resin. As a result, the induction period in the alkaline water washing step, which is a key process step, is shortened, thereby rationalizing the entire process.
Source: http://www.freepatentsonline.com

Innovative process to recycle plastics into petroleum

The present means of waste plastics disposal such as mechanical recycling, land filling and incineration have certain limitations and are inadequate for disposing of the ever increasing amount of waste. Chemical recycling – the conversion of waste plastics to value-added hydrocarbons – is generally accepted as the only feasible solution for the utilization of waste plastics.

The Indian Institute of Petroleum (IIP) of the Council of Scientific and Industrial Research (CSIR), India, has developed a unique process to chemically recycle all polyolefinic waste plastics, particularly polyethylene and polypropylene, into petrol, diesel or aromatics, with simultaneous production of liquefied petroleum gas (LPG). The liquid fuel (petrol or diesel) meets most of the standard fuel specifications (Euro III), while aromatics are rich in benzene, toluene and xylene (BTX). The process is scalable in batch and continuous mode. Preliminary cost analysis suggests that the process would be economical.
Source: http://www.specialchem4polymers.com

Recycling and de-vulcanizing rubber

In Italy, F.Lli Maris S.p.A. and Mr. Gianfranco Maris have jointly filed a patent application on a process for recycling and de-vulcanizing rubber, constituted in particular by industrial manufacturing rejects and/or by articles that have reached the end of their useful life cycle and originate from specialist collection centres and/or landfill sites. The known processes have many disadvantages owing to their specificity that allows only some types of vulcanized elastomeric material to be treated, to the high consumption of energy per unit of de-vulcanized material produced, and to the associated high degree of wear to the machinery used. Those processes also produce a de-vulcanized rubber with a very strong and acrid smell, which has a strong influence on the potential for reuse.

The new process, which seeks to address the above-said disadvantages, essentially consists of two steps. The rubber is first grinded in a mill to reduce it into particles that are substantially between 5 mm and 15 mm. These particles are then mixed well and de-vulcanized rubber product extruded in a twin-screw co-rotating extruder. The extruder has a length 64 times or more the external diameter of the screws that are equipped with mixing elements and is kept at a temperature between 35° and 350°C (about 270°C, preferably) and a rotation speed of between 15 rpm and 300 rpm (about 150 rpm, preferably).

The process is claimed to be very flexible in terms of the starting materials to be treated. In principle, this enables de-vulcanizing of all types of vulcanized rubber or mixtures thereof, such as natural rubber, nitrile rubber, butadiene rubber, ethylene propylene rubber, styrene butadiene rubber, isoprene rubber and chloroprene rubber. In addition, other substances, such as thermoplastic materials or process additives, do not have to be added to said rubbers, and this results in a reduction in process costs as well as in the environmental impact connected to their use. The process is also said to be particularly advantageous in terms of the energy balance. Contact: F.Lli Maris S.p.A., Corso Moncenisio 22, Rosta, I-10090, Italy.
Source: http://www.sumobrain.com

A novel chemical process for recycling material from boats

Most small ships and boats have their hulls and superstructures made using composite materials that contain polyester and glass fibre. Such composites have links that hamper molecular degradation and therefore it is difficult to recycle them. For the past three years, a group formed by the companies Veolia, SINTEF, Reichhold and Nordboat and the Norwegian Composite Association has been conducting research, with support from the Research Council of Norway, to address this problem.

The group has developed an innovative chemical process to separate and reuse the polyester and glass fibre used in boats and other inactive vessels. The process is reported to allow recycling about 80 per cent of the materials. In addition, over 80 per cent of matter is dissolved in two hours and the temperature required for this solution is below 220°C. While the new generation of boats also contain other materials that must be separated, the research results provide hope for the start of a new stage in recycling of boats, according to officials of the company Veolia.
Source: http://materiable.com

ELECTRONIC WASTE

A recycling process for Li-ion batteries

In Germany, scientists from RWTH Aachen University’s Process Metallurgy and Metal Recycling Department, cooperated with the industrial project partners Accurec Recycling GmbH and UVR-FIA GmbH, to develop a recycling process for portable lithium (Li) ion batteries. The process combines a mechanical pre-treatment with hydrometallurgical as well as pyrometallurgical process steps. Therefore, it is possible to recover not only cobalt, but other battery components, especially lithium, as well.

Apart from the characterization and evaluation of all generated metallic material fractions, the researchers focused on the development of a pyrometallurgical process step in an electric arc furnace for the carbo-reductive melting of the fine fraction extracted from spent Li-ion batteries. This fine fraction mainly consists of the electrode material containing cobalt and lithium. Since a selective pyrometallurgical treatment of the fine fraction for producing a cobalt alloy has not been done before, the proof of feasibility was the principal aim. Contact: Mr. Tim Georgi-Maschler, IME Process Metallurgy and Metal Recycling, RWTH Aachen University, D-52056 Aachen, Germany.
Source: http://www.sciencedirect.com

A method for recycling of CRT funnel glass

Finding better solutions to manage and recycle cathode-ray tube (CRT) glass is crucial for reducing the environmental threats due to the disposal of the glass. Mr. Tung-Chai Ling and Mr. Chi-Sun Poon from the Department of Civil and Structural Engineering, Hong Kong Polytechnic University, China, conducted a laboratory study on developing a method for removing lead from crushed funnel glass surface and re-utilizing the treated glass in cement mortar. The results of the study demonstrated that nitric acid at 3-5 per cent concentration levels can be used to remove most of the lead from the crushed funnel glass surface and make it non-hazardous waste based on toxicity characteristics leaching procedure (TCLP) test. It was noted that the particle size of glass and number of treatment cycles are significant factors affecting lead extraction. The study further demonstrated that it is feasible to utilize up to 100 per cent of treated funnel glass as a replacement for natural sand for producing cement mortar. Contact: Mr. Tung-Chai Ling, Department of Civil and Structural Engineering, Hong Kong Polytechnic University, Kowloon, Hong Kong, China.
Source: http://www.tandfonline.com

New electronic waste recycling facility

In Sweden, ABB and Boliden are working together to build a plant at the electronic waste recycling facility at the latter’s Rönnskär copper smelter, with the intent of tripling its recycling capacity. Metal recovery from waste takes 10-15 per cent of the energy required to refine metal from raw ore, the company said. With a capacity of 120,000 tonnes per year, the new Boliden electronic waste recycling facility would be the world’s largest – recovering copper and precious metals from electronic waste using only a fraction of the energy required to extract metals from ore.

The pre-sorted and pre-shredded e-scrap is smelted at Rönnskär using proprietary Kaldo® Furnace Technology. After smelting, the molten metals are transferred to the adjoining production lines for processing into high-grade products. The process also supports the European Union’s Waste Electrical and Electronic Equipment (WEEE) Directive, which requires 4 kg of e-waste to be collected and sorted per head of population in the European Union. This is expected to rise to 13-16 kg per person by 2016.

ABB played a significant role in the Kaldo plant expansion and at the Rönnskär complex as a whole. For the new Kaldo plant, ABB has supplied a comprehensive range of process-critical automation and power technologies, including the process control system. The entire electronic waste recycling process is controlled by ABB’s 800xA Extended Automation System, and includes customized features such as remote operation of the process and an exact positioning system to prevent spilling of hot molten metal from the furnace.
Source: http://m.controleng.com

Reuse of rare earth metals from used vehicles

In Japan, Honda Motor Co. Ltd. and Japan Metals & Chemicals Co. Ltd. have jointly announced the establishment of the world’s first mass-production plant to extract rare earth metals from various used parts in Honda products. Honda will use a process newly developed by Japan Metals & Chemicals for recycling rare earth metals – obtained from used nickel-metal hydride batteries collected from Honda hybrid vehicles at Honda dealers inside and outside of Japan – in not only new nickel-metal hydride batteries but also in a wide range of other Honda products.

Honda had been applying a heat treatment to used nickel-metal hydride batteries and recycling nickel-containing scrap as a raw material of stainless steel. However, the successful stabilization of the extraction process at the plant of Japan Metals & Chemicals made possible the extraction of rare earth metals in a mass-production process with a purity as high as that of newly mined and refined metals. The new process enables the extraction of above 80 per cent of the rare earth metals contained in used nickel-metal hydride batteries.
Source: http://world.honda.com

Noble metal separation from waste PCBs

Henan Province Sanxing Machinery Co. Ltd., China, offers an automated machine for separating noble metals from waste printed circuit boards (PCBs). The machine includes patented equipment for the separation of electrical conductors and non-conductors, PCB disassembling, crushing and pulverizing. The machine, which adopts advanced recycling process by physical methods and high voltage electrostatic separation, offers a high recovery percentage of noble metals with up to 98 per cent purity. To avoid dust pollution, the equipment also uses the three-in-one equipment that has a three-stage dust removal: cyclone dust removal, bag dust removal and dust removal by air cleaner.

The Model SX-1001 machine has an output capacity of 400-800 kg/hour. It has a power rating of 75 kW and occupies an area of 120 m2. Contact: Henan Province Sanxing Machinery Co. Limited, West Gang Xushui Town, Zhongyuan Region, Zhengzhou, Henan, 450042 China. Tel: +86 (371) 6784 2763; Fax: +86 (371) 6784 2730.
Source: http://hnssxjx.en.alibaba.com

Recycling system for insulated wire scrap

Machinery manufacturer Seltek Srl., Italy, has introduced a cable recycling system that is claimed to produce excellent results with insulated wire scrap. The producer of ‘Stokkermill’ brand of recycling equipment says that the compact granulator 3000 Turbo is capable of shredding and separating large quantities of cable with a high operating efficiency. The 3000 Turbo features a vibrating table for dry separation, with the grinding mill consisting of three rotating blades and two fixed blades, each 430 mm long. The granulator boasts a capacity of 250-350 kg per hour and includes an integrated turbo unit to ensure a high quality and purity of even very thin cables, the company states. On request, the machine can be delivered with an integrated pre-grinder and conveyor belt system with magnetic separation. Contact: Seltek Srl., Via Stiria 36, Scala C, 33100 Udine, Italy. Tel: +39 (328) 827 2193; E-mail: info@seltekitalia.it; Website: www.seltekitalia.it.
Source: http://www.recyclinginternational.com

Minimizing e-waste’s environmental impact

Researchers at the University of Florida (UF), the United States, are looking for ways to minimize environmental hazards associated with a material that is likely to play an increasingly important role in the manufacture of these goods in the future. Carbon nanotubes are being used in touch screens and to make smaller, more efficient transistors. If current research to develop them for use in lithium ion batteries is successful, carbon nanotubes could become important technology for powering everything from smartphones to hybrid vehicles. However, there is some concern too.

“Depending on how the nanotubes are used, they can be toxic – exhibiting properties similar to asbestos in laboratory mice,” said Mr. Jean-Claude Bonzongo, an associate professor of environmental engineering at UF College of Engineering. He is involved in a research collaboration with Mr. Kirk Ziegler, a UF associate professor of chemical engineering, to minimize this potential for harm. In particular, they are investigating toxicity associated with aqueous solutions of carbon nanotubes that would be used in certain manufacturing processes.

Exploiting advantageous properties of carbon nanotubes is difficult because the nanotubes tend to clump together, Mr. Ziegler said. Hence, carbon nanotubes have to be treated to keep them dispersed and available for electron interactions that make them good conductors. One way to do it is to mix them with an aqueous solution that acts as a detergent and separates the tangled bundles. However, some of these solutions are toxic or become toxic in the presence of carbon nanotubes, Mr. Bonzongo said. The study focuses on solutions that become hazardous when mixed with the carbon nanotubes. The most recent results indicate that toxicity can be reduced by controlling the ratio of liquid to particulate.
Source: http://www.sciencedaily.com

INDUSTRIAL WASTEWATER

Silver nanoparticles could aid clean-up of mercury in water

A process for creating very fine silver nanoparticles could usher in more effective, cheaper ways of cleaning water contaminated with mercury. At Brighton University, the United Kingdom, a team of scientists says the particles themselves could then be incorporated into industrial processes that use mercury or small-scale filters for dentists and jewellery manufactures.

Brighton’s cost-effective alternative first involves mixing silver with specially modified quartz sand, which reduces silver particles to a nanoscale with a high degree of purity. While other methods such as citrate reduction may leave residual organics, these silver particles are pure, and small as their size can be controlled, says Dr. Kseniia Katok from Brighton. This is important because when the diameter of these nanoparticles drops below a critical 32 nm, they attain a property called ‘hyperstoichiometry’. The upshot is that the ratio of mercury to silver goes from 1:2 to around 1.5:1 – to effectively clean up contaminated water with less silver. Contaminated water could be poured through some kind of filter so that the mercury will be immobilized on the surface of the silver nanoparticles and pure water will come out, Dr. Katok said.

The group will also look at ways of scaling up both the production of the nanoparticles themselves and their deployment in various scenarios. Brighton scientists hope that these findings would enable a key shift towards the use of nanomaterials for wastewater remediation and metal removal and recycling.
Source: http://www.theengineer.co.uk

Improved process for wastewater sludge reduction

The Italian National Research Council’s Water Research Institute (WRI) has developed a new process that can significantly reduce wastewater sludge. The researchers believe that biological treatment plus ozone can reduce the amount of sludge coming from wastewater treatment plants by a factor of ten.

Biological processes are one of the cheapest ways to treat industrial wastewater, but pollutants in industries such as leather, textiles and pharmaceuticals are not easy for microbes to break down. However, the WRI scientists believe that the technology they developed can deal with such waste using a Sequencing Batch Biofilter Granular Reactor (SBBGR), where the microbial biomass grows mainly as granules and breaks down wastes.

The granules are trapped in pores between plastic support material in a reactor and the microbes are in stressed condition, producing less sludge. The microbes are not given suitable conditions to proliferate, so fewer microbes and less waste results. According to Mr. Antonio Lopez, a Project Co-ordinator at WRI, with the new technology only 50 g of sludge is produced for every 1 kg of wastewater processed – significantly less than the average 500 g produced through biological systems. Additionally, integrating ozone with the reactor allows effluents from leather and textile processing to be treated. The ozone also help transform the pollutants into more easily biodegradable compounds, thereby reducing treatment costs.
Source: http://www.pollutionsolutions-online.com

Nanocomposite removes heavy metals from effluent

A semi-crystalline, stable nanocomposite cation-exchange adsorbent was successfully employed by researchers at Aligarh Muslim University (AMU), India, for the treatment of industrial effluent and sewage water to remove heavy metal ions. Using columns packed with this cation-exchange material, several important and analytically difficult quantitative separations of metal ions have been achieved. The nanocomposite can also be used as a conducting material.

The adsorbent was synthesized at pH 1.0 by the sol-gel method and characterised. Ion-exchange capacity, pH titration, elution behaviour and distribution studies were also carried out to determine the primary ion-exchange characteristics of the material. The composite material showed good exchange capacity of 1.47 meq/g (for Na+ ions), besides higher chemical and thermal stability. The adsorbent can be used at up to 200°C with 88 per cent retention of its initial ion-exchange capacity.

The distribution coefficient values (Kd) of metal ions have been determined in various solvent systems. On the basis of Kd values, the material was selective for barium (II), mercury (II) and lead (II) ions. The limit of detection (LOD) and the limit of quantification (LOQ) for lead (II) were found to be 0.97 and 2.93 µg/L, respectively.
Source: http://workingwithwater.filtsep.com

Waterless textile dyeing cuts effluents

The sports goods company Nike Inc., the United States, is adopting a waterless dyeing technology that uses recycled carbon dioxide (CO2) to colour synthetic textiles. The process, which the company has been exploring for eight years, could eliminate the use of countless billions of litres of polluted discharges into waterways near production plants in Asia, where much of the world’s textile dyeing occurs. On average, an estimated 100-150 litres of water is needed to process 1 kg of textile materials. By 2015, more than 39 million tonnes of polyester will be dyed annually, according to industry analysts.

The waterless dyeing process, developed by DyeCoo Textile Systems based in the Netherlands, will begin to show up on Nike products later this year. It utilizes a supercritical fluid CO2 (SCF) technology, which involves heating CO2 to above 31°C and pressurizing it to make it supercritical – a state of matter that can be seen as an expanded liquid or a heavily compressed gas. DyeCoo is believed to be the first company to successfully apply the SCF CO2 process to the commercial dyeing of polyester fabric, and research is underway to apply the technology to cellulosic and synthetic fabrics.

According to DyeCoo, the environmental benefits of its technology include the elimination of water consumption and discharges, the elimination of wastewater as well as effluents from the dyeing process, reductions in air emissions as well as energy use, faster dyeing time, and the elimination of surfactants and other chemicals used in many dyes. It says that 95 per cent of the CO2 used in the process gets recycled. The process also needs less re-dyeing, another massive water consumer.
Source: http://www.greenbiz.com

Nanofiltration enhances textile wastewater treatment

Researchers from the Material Sciences and Environment Laboratory of Sfax University, Tunisia, have studied the use of nanofiltration as a post-treatment after coagulation-flocculation, which was used to treat a mixture of effluents coming from different textile industry operations (dying, bleaching, etc.). The scientists first determined the fluctuation in the characteristics of the different effluents resulting from different treatment steps of cotton clothes. The effects of operating conditions, such as pressure and temperature, on the permeate flux and retention of chemical oxygen demand (COD), colour and salinity were then investigated. The critical flux concept was used to study the effect of salt on nanofiltration performance. It was found that it is more difficult to eliminate the salts when their concentration is higher than 9 g/L.

Nanofiltration experiments showed that the permeate flux was about 24 L/h-m2, obtained at a volume reduction factor (VRF) of 3 under optimal pressure (10 bar) and temperature (40°C). The best pollutant retention was 57 per cent for COD, 100 per cent for colour and 30 per cent for salinity. Finally, it was demonstrated that using microfiltration in place of coagulation-flocculation as pre-treatment prior to nanofiltration leads to enhanced effluent treatment performance, particularly in terms of salinity and COD retention. Contact: Ms. Emna Ellouze, Laboratoire Sciences des Matériaux et Environnement, Faculté des Sciences de Sfax, Université de Sfax, Route de Soukra Km 4, 3000 Sfax, Tunisia.
Source: http://workingwithwater.filtsep.com

Ozone/biofiltration as RO alternative for PPCP removal

A pilot-scale research project at the University of New Mexico, the United States, studied and compared the removal of pharmaceuticals and personal care products (PPCPs) and other micropollutants from treated wastewater by ozone/biofiltration and reverse osmosis. The study found that while ozone/biofiltration and reverse osmosis are comparable for micropollutant removal, ozonation fares better than reverse osmosis in terms of energy consumption, water recovery and waste production. Ozone doses of 4-8 mg/L were nearly as effective as reverse osmosis for removing micropollutants.

The reduction in UV254 absorbance (ultraviolet absorbance at 254 nm) as a function of ozone dose correlated well with the reduction in non-biodegradable, dissolved organic carbon and the simultaneous production of biodegradable dissolved organic carbon (BDOC). BDOC analysis demonstrated that ozone does not mineralize organics in treated wastewater, and that biofiltration can remove organic oxidation products of ozonation. Biofiltration is recommended for treating ozone contactor effluent, to minimize the presence of unknown micropollutant oxidation products in the treated water.
Source: http://workingwithwater.filtsep.com

BIOREMEDIATION

Microbes recover fuel from oil sands

The United States Department of Energy’s Savannah River National Laboratory (SRNL) is patenting a collection of microbes that can be utilized both for addressing energy needs and cleaning up the environment. The surfactant-producing ‘BioTiger’ microbial consortium is the result of more than eight years of extensive work that began at a century-old Polish waste lagoon to develop a microbe-based method for cleaning up oil-contaminated soils. From that lagoon, a team of SRNL and Polish researchers identified microbes that could break down the oil to carbon dioxide and other non-hazardous products.

Recent experiments have shown that BioTiger naturally produces chemicals that may have other industrial uses as well. For example, it can be applied directly for cleaning up oil residues on surfaces such as concrete slabs and building foundations, and for increasing oil recovery from oil sands without added chemicals. Oil sands (tar sands) are a combination of clay, sand, water, and bitumen. Oil sands are mined and processed to generate oil similar to that pumped from conventional oil wells. Extracting oil from these sands, however, is more complex and expensive, requires more energy than standard oil recovery, and is more polluting to the environment. An enhanced oil recovery process using BioTiger could provide a means to maximize capacity and minimize environmental impact, while remaining cost-effective.

BioTiger microbes produce biosurfactants and attach themselves to the oil sands separating the oil from the sand particles. The microbes make the separation step easier, resulting in more removed oil and reduced energy costs. In a test on oil sands, BioTiger demonstrated a 50 per cent improvement in separation over four hours and a five-fold increase in 25 hours. BioTiger also degrades polycyclic aromatic hydrocarbons (PAHs) – pollutants that form one of the most harmful aspects of oil spills.
Source: http://www.engineerlive.com

New in situ aerobic bioremediation

Groundwater remediation equipment specialists Enviro-Equipment Inc., the United States, recently demonstrated ‘OxyGreen’, a new patented in situ aerobic bioremediation system. The demonstration involved placing the OxyGreen Cell in a mock well constructed out of clear plastic for display, and then filling the well with tap water to show the substantial amount of oxygen produced by the device’s in situ electrolysis process. Unlike typical amendments, OxyGreen does not require any injector, chemical or activator. It also runs non-stop until the job is done via a standard 120 V power source or a solar panel. According to Mr. Brian E. Chew, Vice President of Enviro-Equipment Inc., the new OxyGreen system applies electrolysis process in a new way – one that does not require injection permits, multiple injection events, an injection rig or injection well installation. Contact: Mr. Brian Chew, Enviro-Equipment Inc., 11180 Downs Road, Pineville, NC 28134, United States of America. Tel: +1 (704) 556 7723; Fax: +1 (704) 588 5119; E-mail: brianchew@enviroequipment.com; Website: www.enviroequipment.com.
Source: http://www.prweb.com

Bioremediation of soil contaminated with lead

Lead (Pb) has been recognized as one of the most emerging hazardous heavy metals that pollute soil. Soil lead pollution is very serious in many cities of China. The soil of Urumqi, an economically fast developing city in northwestern arid China, is known to be highly contaminated with lead. Conventional lead removal methods have several disadvantages, such as less effective metal-ion removal, high reagent requirement and the problem of safe disposal of the pollutant. Bacterial methods for removal of lead from contaminated sites provide an attractive alternative to physicochemical methods. According to previous studies, biomineralization based on microbially induced calcite precipitation (MICP) provides a promising technique to remediate toxic metals from contaminated soils with additional advantages over current bioremediation techniques.

Scientists at the State Key Laboratory of Desert and Oasis Ecology, Xinjiang Institute of Ecology and Geography, China, investigated the usage of the calcite-precipitating bacterium Kocuria flava (CR1 strain) for Pb bioremediation in soils collected from a farmland in Urumqi. The bacterium was able to grow on nutrient agar media supplemented with 50 mM Pb2+ [Pb(NO3)2]. The results showed that incubating contaminated soil with K. flava CR1 could reduce the active Pb, alleviate the Pb stress and stabilize the Pb contaminated soil. The wide distribution of MICP and the ability of its products to trap heavy metals may provide a new in situ remediation method for contaminated soil. This process can be widely used in the remediation of heavy metals, even in arid areas where phytoremediation cannot be successful. Moreover, MICP is not sensitive to redox potential, which makes this process highly effective in bioremediation. Contact: State Key Laboratory of Desert and Oasis Ecology, Xinjiang Institute of Ecology and Geography, Chinese Academy of Sciences, Urumqi 830011, China.
Source: http://english.cas.cn

Bioremediation for water contamination

In the United States, JRW Bioremediation LLC and Archer Daniels Midland Company have jointly filed a patent application on methods for bioremediation of contaminants in water using soapstock, an acid oil of soapstock, a neutralized acid oil of soapstock or combinations thereof. In one embodiment, a method comprises placing in contact with water the said composition, along with a compound selected from the group consisting of an emulsifier, a lactate ester, a lactate polymer, a polyhydric alcohol, carboxylic acids, salts of carboxylic acids, and any of their combinations.

In another embodiment, the composition comprises a first component selected from the group consisting of soapstock, acid oil of soapstock, a neutralized acid oil of soapstock and any combinations thereof; and a second component selected from the group consisting of ethoxylated monoglyceride, lecithin, sodium stearoyl lactylate, polylactate, ethyl lactate, a carboxylic acid, a salt of a carboxylic acid and any of their combinations. Upon placement of 0.2 mL of the composition in 100 mL of water comprising an amount of contaminant and a mixed culture of halo-respiring bacteria, at least a portion of the amount of contaminant is converted into an innocuous derivative after a period of time.
Source: http://www.freepatentsonline.com

Novel method of cleansing toxins from oil sands

Oil sand, which contains bitumen, needs to be treated before it can be used to produce usable fuels such as petrol and diesel. Oil sand processing requires vast amounts of water, which result in toxic tailings ponds that are a significant risk to the environment. In Canada, biologists at Calgary University and engineers at Alberta University have collaborated to develop a method of cleaning toxins from oil sands. The method makes use of biofilms “that are indigenous to the oil sands environment and highly tolerant to the stress associated with toxins and metals found in tailings water,” said Prof. Raymond Turner of Calgary University. The biofilm consortia could eventually be used also to detoxify the wastewater.

Prof. Turner and his team are growing biofilms on the support material to test in bioreactors that are being developed at the Alberta University. “By altering the growth conditions and exposing the biofilms to different stressors, we could select for or against certain species, and we began to learn how we could manipulate the biofilms to get the metabolic activities and characteristics we were looking for,” Prof. Turner said. The ultimate goal is to develop tailings water treatment plants for all the oil sands operations.
Source: http://www.theengineer.co.uk

Metal-reducing bacteria for degrading hydrocarbons

Micro-organisms from anoxic environments have the ability to reduce numerous metals as part of anaerobic growth. They are capable of using a wide range of organic compounds, including organic acids, sugars and extracts as substrates for growth. However, very few studies have looked at the utilization of hydrocarbons linked to metal reduction; a vast majority of hydrocarbon degradation studies have been carried out under aerobic conditions.

In a recent study by scientists from Griffith University, Australia, a comprehensive screening program revealed positive enrichment cultures where the reduction of metals iron (Fe), arsenic (As) and molybdenum (Mo) was linked to growth on various hydrocarbons in Soda Lake, oil reservoir, aquifer and contaminated oil refinery soil samples.

Three hydrocarbons – diesel, hexadecane and kerosene – and three polycyclic aromatic hydrocarbons (PAHs) – phenanthrene, anthracene and pyrene – were used. Two pure bacteria were isolated from enrichments and studied further. Strain BP5, isolated from an oil reservoir in the Great Artesian Basin, coupled the reduction of Fe(III) to pyrene and anthracene degradation. Strain Cal-A was isolated from Caltex oil refinery soil and was able to link anthracene degradation to Fe(III) reduction. They are the first reported isolates capable of degrading either 3 or 4-ringed PAHs linked to Fe(III) reduction. Anaerobic degradation of hydrocarbons, particularly PAHs, is likely to represent an important process in the future for clean up of contaminated aquifers and other sub-surface environments.
Source: http://www.asm2012.org

AIR POLLUTION CONTROL

A simple, efficient process for CO2 recycling

A new generation of catalysts can be used to simultaneously recycle two types of industrial waste: carbon dioxide (CO2) and polymethylhydrosiloxane (PMHS), a silicon production waste. Researchers from the French Commissariat à l’Energie Atomique (CEA) and Le Centre National de la Recherche Scientifique (CNRS) have developed a simple catalysed chemical reaction that allows these two types of industrial waste to be used to produce formamides – compounds used in the industrial manufacture of adhesives, solvents and medical products. This optimized recycling process also makes it possible to synthesize a greater number of different compounds, thus extending its scope of application to new fields.

The new process developed produces formamides from CO2 in one step, under environmentally safe conditions. This formylation reaction has the advantage of presenting a high yield: one formamide molecule produced for each CO2 molecule consumed. The use of a new generation of carbene-type catalysts (2,000 times more reactive than those previously used) allows for simplified reaction conditions (atmospheric pressure, ambient temperature, etc.). Most importantly, these new catalysts can also be used with PMHS, a low-reactivity molecule. In the past, the reaction was obtained through the interaction of CO2 with silane, an expensive sub-product of electronic and photovoltaic production processes. The new catalysts make it possible to use PMHS instead of silane, thus basing the reaction on the simultaneous recycling of two industrial wastes. The principle behind the process could solve a number of problems posed by current production systems – waste processing costs, environmental and health impact, depletion of energy sources, etc.
Source: http://www.cea.fr

Fingerprinting air pollution

A research team from the University of Pittsburgh (Pitts) and the Electric Power Research Institute (EPRI), the United States, collected emissions samples from several power plant stacks in the country and developed a unique method for the detection of the isotopic signatures of nitrogen oxide (NOx) emissions under different configurations. These isotopic signatures will be instrumental in helping to identify emission sources of air pollution across the nation.

The researchers developed a process for extracting NOx emission samples from the stacks of different types of coal-fired power plants and measuring their isotopic composition. They discovered that emissions from power plants employing advanced NOx controls differed with those plants without the advanced technologies or NOx emissions from other sources in the proportions of the 15N atom in the NOx emitted. With this information, the scientists will be able to analyse deposition samples and better determine the sources contributing to the deposited NOx products. According to Ms. Emily Elliott, principal investigator and assistant professor in the Pitts Kenneth P. Dietrich School of Arts and Sciences, “These ‘isoscapes’ can only be interpreted with fingerprint data like the isotopic signatures collected in this study.”

Ms. Elliott’s lab utilized bacteria to convert nitrate in the NOx collected into a gaseous form for isotopic analysis. Earlier analytical approaches were time- and labour-intensive, and precluded widespread characterization of environmental nitrate isotopes. The new method saves both time and effort. The results of analyses, combined with additional information from other NOx sources, will allow scientists to look at rain samples and determine how much nitrogen comes from power plants stacks, as opposed to how much comes from such other sources as motor vehicles, lightning or soil. “It was important for us to understand how the implementation of emission control technologies affects the isotopic nature of the NOx being emitted in order to evaluate its fate in the atmosphere,” Ms. Elliot said.
Source: http://www.phys.org

A new material for CO2 capture

Hitachi Ltd., Japan, has developed a solid adsorbent material made by using cerium oxide for collecting and accumulating carbon dioxide (CO2) produced by coal-fired power generation. Hitachi has also increased the number of adsorption sites of the new adsorbent material by using its exhaust purification catalyst technologies so that more CO2 can be adsorbed. Specifically, to increase adsorption efficiency, a second component that attracts CO2 was added to the surface of the adsorbent material. Compared with zeolitic solid adsorbents, the amount of CO2 adsorbed by the new material is about 13 times larger, the company said.

Hitachi utilized a template method for forming pillar-shaped fine pores, which are regular hollow structures, on cerium oxide. As a result, CO2 molecules are dispersed inside the fine pores and are more likely to contact with the adsorption sites, thereby improving the rate of CO2 adsorption.

Currently, for collecting CO2, the new method using the solid adsorbent material requires an amount of energy equivalent to that needed by the chemical absorption technique using amine fluid. Hitachi plans to reduce the required amount of energy by an additional 20 per cent or more by improving the solid adsorbent material and by building an optimal system, with the aim of commercializing the new material in or after 2025.
Source: http://techon.nikkeibp.co.jp

A catalyst to make CO2 into fuel

Researchers at the Massachusetts Institute of Technology (MIT), the United States, have created a stable catalyst that can convert carbon dioxide (CO2) to fuel while using only a trickle of electricity. The material can be used to recycle waste gases, curbing greenhouse emissions, as well as for creating useful products, like methane, which could be sold to offset pollution reduction costs and provide another energy source. The new recipe, which uses a blend of copper and gold formed into nanoparticles, overcomes some of the earlier challenges to developing an efficient way to recycle carbon.

“Copper is an attractive metal for carbon dioxide reduction,” explained Ms. Kimberly Hamad-Schifferli, an associate professor in mechanical engineering at MIT. The metal is generally cheap and reacts in well-understood ways. However, it oxidizes when it is exposed to air and moisture, turning from a lustrous brown to a pale green, rendering the metal ineffective as a catalyst, she noted. Since the reaction takes place on material’s surface, the researchers make the process more efficient by forming the copper into tiny particles, thereby increasing the catalyst’s surface area. However, doing this accelerates oxidation as well, rendering the substance inert in as little as 20 minutes.

To address this issue, Ms. Hamad-Schifferli and her colleagues mixed in gold, a relatively stable metal that drastically slowed oxidation to several days. The scientists mixed gold and copper salts in a solution and heated it to form the hybrid particles. The experiment indicated that the CO2 binds to their surface, reacts to form methane and other hydrocarbons and then moves along quickly, allowing the reactions to progress. To use the catalyst, CO2 needs to be dissolved in a liquid. The fluid then must flow over the copper and gold as a voltage is applied, producing hydrocarbon fuels, which are then harvested. Though gold is more expensive than pure copper, the efficiency and durability improvements and the reaction products can offset the increasingly pricey metal’s upfront costs.
Source: http://www.eenews.net

New materials remove CO2 from the air

Scientists have reporting a way to remove carbon dioxide (CO2) from smokestacks and other sources, including the atmosphere, achieving some of the highest CO2 removal capacity ever for real-world conditions where the air contains moisture. Existing methods for removing CO2 from smokestacks and other sources are energy-intensive, don’t work efficiently and have other drawbacks. In an effort to overcome such obstacles, Mr. Alain Goeppert and colleagues from the Department of Chemistry, University of Southern California, the United States, turned to solid materials based on polyethylenimine, a readily available and inexpensive polymeric material.

Their tests showed that these inexpensive materials achieved some of the highest CO2 removal rates ever reported for humid air, under conditions that stymie other related materials. After capturing CO2, the materials give it up easily so that the CO2 can be utilized in making other substances, or permanently isolated from the environment. The capture material then can be recycled and reused many times over without losing efficiency. Contact: Mr. Alain Goeppert, Department of Chemistry, University of Southern California, University Park, Los Angeles, California, CA 90089-1661, United States of America. E-mail: goeppert@usc.edu.
Source: http://www.sciencedaily.com

CO2 capture process ready for big projects

In Germany, a pilot project carried out by Siemens AG and E.ON AG has demonstrated that carbon dioxide (CO2) emissions from power plants can be captured effectively. More than 90 per cent of the greenhouse gas was captured from a part of the flue gas at the Staudinger coal-fired power plant near Hanau, Germany. The results of the pilot project, running from 2009, will allow further demonstration projects and calculation of investment and operating costs. It was also shown that the flue gas scrubbing process does not reduce the plant’s efficiency to the extent expected and that the Siemens PostCap process produces nearly no emissions.

Separation of CO2 from power plant exhaust gases is one of the ways in which plants that run on fossil fuels can help protect the climate. The CO2 is removed from the flue gas using Siemens’ post-combustion process, and captured with a special scrubbing agent consisting of an aqueous amino acid salt solution. The amino acid salt solution is almost completely non-volatile – it generates practically no solvent emissions – and is not harmful to the environment. Unlike previous processes, the new method does not require extensive cleaning of the flue gas after the CO2 is captured. Furthermore, the scrubbing agent removes other pollutants in the flue gas besides CO2 and can be reused repeatedly.

Besides being very environmentally friendly, the process is also energy efficient. The Siemens process is suited for new power plants using fossil fuels as well as for retrofitting existing power stations. Siemens has a comprehensive, technologically optimized package for CO2 capture. This technology is part of the Siemens environmental portfolio, which generated around 28 billion euros in sales for the company in fiscal year 2010. Contact: Siemens AG, Energy Sector, Freyeslebenstrasse 1, 91058 Erlangen, Germany. Tel: +49 (180) 524 7000; Fax: +49 (180) 524 2471; E-mail: support.energy@siemens.com.
Source: http://www.siemens.com

Oxygen-separation membranes could aid in CO2 reduction

It may seem counterintuitive – but one way to reduce carbon dioxide (CO2) emissions to the atmosphere may be to produce pure CO2 in power plants that burn fossil fuels. In this way, greenhouse gases (GHGs) isolated within a plant could be captured and stored in natural reservoirs, deep in the Earth’s crust. Such “carbon-capture” technology might greatly reduce GHGs emissions from cheap and abundant energy sources such as coal and natural gas, and help minimize fossil fuels’ contribution to climate change. But extracting CO2 from the rest of a power plant’s by-products is now an expensive process requiring huge amounts of energy, special chemicals and extra hardware.

Researchers at the Massachusetts Institute of Technology (MIT) are evaluating a system that efficiently eliminates nitrogen from the combustion process, delivering a pure stream of CO2 after removing other combustion by-products such as water and other gases. The centrepiece of the system is a ceramic membrane used to separate oxygen from air. Burning fuels in pure oxygen, as opposed to air – a process known as oxyfuel combustion – can yield a pure stream of CO2. The researchers have built a small-scale reactor in their lab to test the membrane technology, and have begun establishing parameters for operating the membranes under the extreme conditions found inside a conventional power plant.

Ceramic membranes are selectively permeable materials through which only oxygen can flow. These membranes, made of metal oxides such as lanthanum and iron, can withstand extremely high temperatures – a huge advantage when it comes to operating in the harsh environment of a power plant. Ceramic membranes separate oxygen using a mechanism called ion transport, whereby oxygen ions flow across a membrane, drawn to the side of the membrane with less oxygen. Mr. Ahmed Ghoniem, the Ronald C. Crane Professor of Engineering at MIT, says that ceramic membrane technology may be an inexpensive, energy-saving solution for capturing CO2. “The whole objective behind this technology is to continue to use cheap and available fossil fuels, produce electricity at low price and in a convenient way, but without emitting as much CO2 as we have been,” he says.

Mr. Ghoniem and his colleagues built a small-scale reactor with ceramic membranes and studied the resulting oxygen flow. They observed that as air passes through a membrane, oxygen accumulates on the opposite side, finally slowing the air-separation process. To avert this build-up of oxygen, the group built a combustion system into their model reactor. They found that with this two-in-one system, oxygen passes through the membrane and mixes with the fuel stream on the other side, burning it and generating heat. The fuel burns the oxygen away, making room for more oxygen to flow through. According to Mr. Ghoniem, the system offers a “win-win situation,” enabling oxygen separation from air while combustion occurs in the same space.
Source: http://www.pennenergy.com

RECENT PUBLICATIONS

Asia Pacific Renewable Energy Policy Handbook 2012

Asia Pacific Renewable Energy Policy Handbook 2012 is the latest policy report from GlobalData that offers comprehensive information on major policies governing renewable energy market in the region. The report presents an in-depth analysis of renewable energy policies across the major countries in the Asia Pacific – China, India, Australia, New Zealand, Republic of Korea, Japan, Indonesia and Thailand. It details the key policy instruments adopted by some of the major and emerging nations that led to huge development in the renewable industry of the region. The report also provides insights to major policy initiatives taken up by Central Administration of China, India, Australia, Republic of Korea and others for the market development of renewable energy sources such as wind, solar, geothermal, biopower and biofuels. It also describes major technology-specific policies and incentives provided in each of these countries.

Contact: ReportsandReports, Dominion Plaza, 17304, Preston Road, Suite 800, Dallas, TX 75252, United States of America. Tel: +1 (888) 391 5441; Website: www.reportsnreports.com.

The Power of Design: Product Innovation in Sustainable Energy Technologies

Unique in linking sustainable energy technologies with innovation and product design, this book offers clear explanation of both and case studies enabling readers to understand and design energy-efficient products in several different markets. The book integrates the subject areas that are necessary for the design of sustainable and energy-efficient products based on sustainable energy technologies. The theory provided is supported by cases of design projects and concepts in practice. The book’s methodological approach enables the reader to apply the information and examples in their research and design projects. This book fills a void in existing literature at the intersection of innovation processes, sustainable energy technologies, energy demand reduction, product development, and user behaviour, which requires an integrated view on the development of sustainable energy solutions.

Contact: John Wiley & Sons Singapore Pte. Ltd., CWT Commodity Hub, 24 Penjuru Road, #08-01, Singapore 609128. Tel: +65 6302 9838; Fax: +65 6265 1782; E-mail: asiacart@wiley.com.


ASIAN AND PACIFIC CENTRE FOR TRANSFER OF TECHNOLOGY

This website is optimized for IE 8.0 with screen resolution 1024 x 768
For queries regarding this website, contact us
Copyright © 2010 APCTT | Privacy Policy | Disclaimer | Feedback